Projects

Selected engineering projects in HVAC, controls, mechanical design, drafting, and computational tools.

AutoCAD SolidWorks HVAC · Cooling Load Automation & Controls MATLAB Machine Learning

Engineering Drawing Portfolio — AutoCAD 2026

Independent work · July 2026  ·  Original .dwg and .pdf files on GitHub  ·  Portfolio PDF

Independent drafting portfolio covering two mechanical drawings and one residential floor plan. The work includes orthographic and sectional views, assembly drawings, dimensioning, hatching, layers, blocks, and drawing-sheet preparation.

  • IC engine crankshaft — four-throw crankshaft detail with sections A-A and B-B, flywheel bolt circle, centerlines, and linear, diametral, radial, and angular dimensions.
  • Screw jack — seven component drawings with material specifications and a half-sectional view of the complete assembly.
  • Residential floor plan — two-bedroom single-storey layout with wall hatching, door swings, furniture and fixture blocks, parking, landscaping, and dimensions on all sides.
Detail drawing of a four-throw IC engine crankshaft with cross sections and dimensions
Four-throw crankshaft detail with two sectional views and full dimensioning.
Screw jack component details and half-sectional assembly drawing
Seven screw-jack components and the half-sectional assembly view.
Two-bedroom residential floor plan with dimensions, furniture, parking and landscaping
Residential floor plan with room layout, blocks and hatching.

Skills: AutoCAD, 2D drafting, orthographic and sectional views, assembly drawings, dimensioning, hatching, layers, blocks

Automatic Juice Making Machine

BUET · Mechanical design and fabrication project

Designed and fabricated a lime-juice machine based on a rotating squeezing mechanism. I modeled the rotating parts in SolidWorks, prepared the geometry for manufacturing, and produced the parts by molding and aluminum casting in the BUET foundry lab. The cast parts were then assembled into the machine and tested as a working prototype.

SolidWorks model of the rotating squeezing component
SolidWorks model of the rotating squeezing component.
Split wooden pattern prepared for sand casting
Split wooden pattern prepared for the sand mold.
Fabricated machine with the cast aluminum components installed.
Prototype during functional testing.

Skills: SolidWorks, mechanical design, sand molding, aluminum casting, fabrication, prototyping

HVAC Cooling Load Calculation — CLTD/CLF Method

Independent project · September 2026  ·  Full report (PDF)

Problem: estimate the peak cooling load and required air-conditioning capacity for a 100 m² single-zone space at the 5 PM design condition.

What I did: carried out a component-by-component CLTD/CLF calculation. I calculated roof and wall U-values from construction resistances, corrected the tabulated CLTD values for the design date and outdoor conditions, and included conductive and solar gains through the glazing. The calculation also includes sensible and latent outdoor-air loads at 1 ACH and internal gains from lighting, occupants, and equipment.

Result: the peak load was 13.25 kW (3.77 TR). With the 10% design allowance used in the project, the required capacity was about 4.1 TR, so a nominal 4.5 TR unit was selected. The west-facing glass contributed about 2.43 kW of solar load, and lighting was the largest single load in the final breakdown.

Plan of the conditioned space and surrounding wall conditions
Room layout, envelope construction, glazing, and surrounding conditions used in the calculation.
Cooling load summary showing sensible and latent components
Cooling-load breakdown at the 5 PM design condition.

Skills: cooling-load calculation, CLTD/CLF method, ASHRAE tables, U-value calculation, psychrometrics, equipment sizing

Chilled-Water Automation and Process Control

Eskayef Pharmaceuticals Ltd. · 2020

A process chilled-water line was being controlled manually, which required frequent operator attention and allowed the process temperature to fluctuate. I built a simple automatic control using an Autonics TC4W temperature controller, relay, and solenoid valve so that chilled-water flow responded directly to the temperature setpoint.

I also worked on a stepper-motor-driven peristaltic filling pump whose driver did not have a suitable pulse input available. I built an LM555 astable multivibrator circuit to generate an approximately 3 kHz pulse signal for the stepper-motor driver.

The chilled-water control replaced routine manual valve operation, and the custom pulse circuit provided the control signal needed to run the filling pump.

Autonics TC4W temperature controller
TC4W controller
Electromechanical relay
Relay
Solenoid valve for chilled-water control
Solenoid valve
Circuit breaker for the control system
Breaker
Stepper motor driver and power supply
Stepper driver
Control circuit wiring
Control wiring
Stepper motor used with the peristaltic filling pump
Stepper motor
LM555 astable multivibrator circuit
LM555 pulse circuit

Skills: temperature control, process automation, instrumentation, relay logic, solenoid valves, stepper-motor control, basic circuit design

Digital Psychrometric Calculator in MATLAB

BUET · Numerical Analysis group project · 2016  ·  Full report (PDF)

Built a MATLAB program and graphical interface that calculates psychrometric properties from dry-bulb and wet-bulb temperature. The program returns relative humidity, humidity ratio, dew-point temperature, specific volume, and enthalpy.

Saturation-pressure data were taken from thermodynamic property tables and interpolated for use between tabulated temperatures. The project combined the psychrometric equations, data lookup and interpolation, and a simple GUI so the calculations could be repeated without reading each property manually from a printed chart.

MATLAB graphical interface for psychrometric calculations
MATLAB interface showing the calculated air properties from dry- and wet-bulb temperatures.
MATLAB code used to calculate psychrometric properties
Main calculation routine for humidity ratio, relative humidity, dew point, enthalpy, and specific volume.
MATLAB interpolation function for saturation pressure
Interpolation routine used between tabulated saturation-pressure values.
Spline interpolation of thermodynamic saturation data
Saturation-pressure data from the property tables with spline interpolation.

Skills: MATLAB, psychrometrics, thermodynamics, numerical interpolation, GUI development

Machine Learning Projects

Independent work  ·  Projects and code on GitHub

Small projects used to practice data preparation, model development, visualization, and prediction across several types of machine-learning problems.

  • Mall customer segmentation — K-means clustering using annual income and spending score.
  • Stock price forecasting — time-series forecasting with Prophet, including forecast intervals.
  • Brain tumor classification — MRI image classification using a Vision Transformer.
  • Fake news classification — text classification of news articles.
  • House price prediction — regression on housing data.
  • Used car price prediction — regression using vehicle listing data.
K-means clustering of mall customers into five segments
K-means customer segmentation with five clusters and their centroids.
Prophet stock price forecast with forecast interval
Prophet time-series forecast with the historical series and forecast interval.

Skills: Python, scikit-learn, PyTorch, clustering, regression, classification, time-series forecasting, data analysis